SR-IOV in Openstack – Various Tips, Hacks and Setups

Single Root I/O virtualization (SR-IOV) in networking is a very useful and strong feature for virtualized network deployements.

SRIOV is a specification that allows a PCI device, for example a NIC or a Graphic Card, to share access to its resources among various PCI hardware functions:

Physical Function (PF) (meaning the real physical device), from it a number of one or more Virtual Functions (VF) are generated.

Supposedly we have one NIC and we want to share its resources among various Virtual Machines, or in terms of NFV various VNFCs of a VNF.

We can split the PF into numerous VFs and distribute each one to a different VM.

The routing and forwarding of the packets is done through L2 routing where the packets are forwarded to the matching MAC VF.

The purpose of this post is to share a few tips and hacks we came across during our general activities related to SRIOV.

A very good tutorial for SRIOV setup : https://samamusingworld.wordpress.com/2015/01/10/sriov-pci-passthrough-feature-with-openstack/

 

SRIOV VF Mirroring

Let’s say you want to send the same flows and packets to 2 VMs simultaneously.

if you enter the ip link show you should see something like this:

p2p1: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether a0:36:9f:68:fc:f4 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 00:00:00:00:00:00, spoof checking on, link-state auto
vf 1 MAC fa:16:3e:c0:d8:11, spoof checking on, link-state auto
vf 2 MAC fa:16:3e:a1:43:57, spoof checking on, link-state auto
vf 3 MAC fa:16:3e:aa:33:59, spoof checking on, link-state auto

In order to perform our mirroring and send all traffic both ways we need to change the MAC address both on the VM and on the VF and disable the spoof check.

Let’s change vf2 -> vf3

On the VM:

ifconfig eth0 down
ifconfig eth0 hw ether fa:16:3e:aa:33:59
ifconfig eth0 up

On the host – VF:

ip link set eth0 down
ip link set eth0 vf 2 mac fa:16:3e:aa:33:59
ip link set eth0 vf 2 spoofchk off
ip link set eth0 up

After that we have 2 VFs with the same MAC.

But it will still do not work. What you have to do is, change again the vf 2 to something resembling the latest MAC

ip link set eth0 vf 2 mac fa:16:3e:aa:33:58

After these changes through the experiments we performed we managed to mirror the traffic on 2 different VFs.

 

SRIOV Openstack setup with flat networking – no VLAN

In openstack the default setup and various tutorials use the VLAN networking. Meaning the routing is done through MAC and VLAN.

In one of our tests we had trouble creating traffic matching both rules, so we investigated the no VLAN option.

Even though the setup of SRIOV over flat networking in Openstack is pretty simple, we did not find any tutorial, or a note underlining its simplicity.

The steps are pretty straightforward :

neutron net-create –-provider:physical_network=physnet1 –-provider:network_type=flat <Network_Name>
neutron subnet-create <Network_Name> <CIDR> –name <Subnet_Name> –allocation-pool=<start_ip>, end=<end_ip>
neutron port-create <Network_Id>  –binding:vnic-type direct

And launch VM with port you have just created.

nova boot –flavor <Flavor_Id> –image <Image-id> –nic port-id=<Port_Id> <VM_Name>

 

1 reply
  1. honser
    honser says:

    Hi,

    Thank you for your interesting post, because it’s not easy to capture packet from VF or PCI-PT interfaces.
    I was going to test this, but doesn’t work.
    Do I need to down and up the eth0 again after changing it to resembling mac?
    After all of that processes,
    vm mac == vf2 (fa:16:3e:aa:33:59)
    right?
    Any information will be very appreciated.

    Regards,
    Hongseo

    Reply

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply

Your email address will not be published. Required fields are marked *